2019 Good Quality Alloy Steel Pipe Properties - Seamless carbon steel and alloy mechanical tubes – Sanonpipe
2019 Good Quality Alloy Steel Pipe Properties - Seamless carbon steel and alloy mechanical tubes – Sanonpipe Detail:
Overview
Application
It Is Mainly Used for mechanical and used to make gas cylinders.
Main Grade
1018,1026,8620,4130,4140
Chemical Component
TABLE 1 Chemical Requirements of Low-Carbon Steels
| Grade | Chemical Composition Limits, % | |||||||
| Designation | CarbonA | ManganeseB | Phosphorus,B | Sulfur,B | ||||
| max | max | |||||||
| MT X 1015 | 0.10–0.20 | 0.60–0.90 | 0.04 | 0.05 | ||||
| MT 1010 | 0.05–0.15 | 0.30–0.60 | 0.04 | 0.05 | ||||
| MT 1015 | 0.10–0.20 | 0.30–0.60 | 0.04 | 0.05 | ||||
| MT 1020 | 0.15–0.25 | 0.30–0.60 | 0.04 | 0.05 | ||||
| MT X 1020 | 0.15–0.25 | 0.70–1.00 | 0.04 | 0.05 | ||||
B Limits apply to heat analysis; except as required by 6.1, product analyses are subject to the applicable additional tolerances given in Table 5.
TABLE 2 Chemical Requirements of Other Carbon Steels
|
Grade |
Chemical Composition Limits, %A |
||||
|
Designation |
|||||
|
Carbon |
Manganese |
Phosphorus, |
Sulfur, |
||
|
max |
max |
||||
|
1008 |
0.10 max |
0.30–0.50 |
0.040 |
0.050 |
|
|
1010 |
0.08–0.13 |
0.30–0.60 |
0.040 |
0.050 |
|
|
1012 |
0.10–0.15 |
0.30–0.60 |
0.040 |
0.050 |
|
|
1015 |
0.13–0.18 |
0.30–0.60 |
0.040 |
0.050 |
|
|
1016 |
0.13–0.18 |
0.60–0.90 |
0.040 |
0.050 |
|
|
1017 |
0.15–0.20 |
0.30–0.60 |
0.040 |
0.050 |
|
|
1018 |
0.15–0.20 |
0.60–0.90 |
0.040 |
0.050 |
|
|
1019 |
0.15–0.20 |
0.70–1.00 |
0.040 |
0.050 |
|
|
1020 |
0.18–0.23 |
0.30–0.60 |
0.040 |
0.050 |
|
|
1021 |
0.18–0.23 |
0.60–0.90 |
0.040 |
0.050 |
|
|
1022 |
0.18–0.23 |
0.70–1.00 |
0.040 |
0.050 |
|
|
1025 |
0.22–0.28 |
0.30–0.60 |
0.040 |
0.050 |
|
|
1026 |
0.22–0.28 |
0.60–0.90 |
0.040 |
0.050 |
|
|
1030 |
0.28–0.34 |
0.60–0.90 |
0.040 |
0.050 |
|
|
1035 |
0.32–0.38 |
0.60–0.90 |
0.040 |
0.050 |
|
|
1040 |
0.37–0.44 |
0.60–0.90 |
0.040 |
0.050 |
|
|
1045 |
0.43–0.50 |
0.60–0.90 |
0.040 |
0.050 |
|
|
1050 |
0.48–0.55 |
0.60–0.90 |
0.040 |
0.050 |
|
|
1518 |
0.15–0.21 |
1.10–1.40 |
0.040 |
0.050 |
|
|
1524 |
0.19–0.25 |
1.35–1.65 |
0.040 |
0.050 |
|
|
1541 |
0.36–0.44 |
1.35–1.65 |
0.040 |
0.050 |
|
A The ranges and limits given in this table apply to heat analysis; except as required by 6.1, product analyses are subject to the applicable additional toler-ances given in Table Number 5.
|
TABLE 3 Chemical Requirements for Alloy Steels |
|||||||||
|
NOTE |
1—The ranges and limits in this table apply to steel not exceeding 200 in.2 (1290 cm2) in cross-sectional area. |
||||||||
|
NOTE |
2—Small quantities of certain elements are present in alloy steels which are not specified or required. These elements are considered as incidental |
||||||||
|
and may be present to the following maximum amounts: copper, 0.35 %; nickel, 0.25 %; chromium, 0.20 %; molybdenum, 0.10 %. |
|||||||||
|
NOTE |
3—The ranges and limits given in this table apply to heat analysis; except as required by 6.1, product analyses are subject to the applicable |
||||||||
|
additional tolerances given in Table Number 5. |
|||||||||
| GradeA,B | Chemical Composition Limits, % | |||||||
| Designa- | ||||||||
| Carbon | Manganese | Phospho- | Sulfur,C,D | Silicon | Nickel | Chromium | Molybde- | |
| tion | ||||||||
| rus,Cmax | max | num | ||||||
| 1330 | 0.28–0.33 | 1.60–1.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | … |
| 1335 | 0.33–0.38 | 1.60–1.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | … |
| 1340 | 0.38–0.43 | 1.60–1.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | … |
| 1345 | 0.43–0.48 | 1.60–1.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | … |
| 3140 | 0.38–0.43 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 1.10–1.40 | 0.55–0.75 | … |
| E3310 | 0.08–0.13 | 0.45–0.60 | 0.025 | 0.025 | 0.15–0.35 | 3.25–3.75 | 1.40–1.75 | … |
| 4012 | 0.09–0.14 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.15–0.25 |
| 4023 | 0.20–0.25 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.20–0.30 |
| 4024 | 0.20–0.25 | 0.70–0.90 | 0.04 | 0.035−0.050 | 0.15–0.35 | … | … | 0.20–0.30 |
| 4027 | 0.25–0.30 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.20–0.30 |
| 4028 | 0.25–0.30 | 0.70–0.90 | 0.04 | 0.035−0.050 | 0.15–0.35 | … | … | 0.20–0.30 |
| 4037 | 0.35–0.40 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.20–0.30 |
| 4042 | 0.40–0.45 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.20–0.30 |
| 4047 | 0.45–0.50 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.20–0.30 |
| 4063 | 0.60–0.67 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.20–0.30 |
| 4118 | 0.18–0.23 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.40–0.60 | 0.08–0.15 |
| 4130 | 0.28–0.33 | 0.40–0.60 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | 0.15–0.25 |
| 4135 | 0.32–0.39 | 0.65–0.95 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | 0.15–0.25 |
| 4137 | 0.35–0.40 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | 0.15–0.25 |
| 4140 | 0.38–0.43 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | 0.15–0.25 |
| 4142 | 0.40–0.45 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | 0.15–0.25 |
| 4145 | 0.43–0.48 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | 0.15–0.25 |
| 4147 | 0.45–0.50 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | 0.15–0.25 |
| 4150 | 0.48–0.53 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | 0.15–0.25 |
| 4320 | 0.17–0.22 | 0.45–0.65 | 0.04 | 0.04 | 0.15–0.35 | 1.65–2.00 | 0.40–0.60 | 0.20–0.30 |
| 4337 | 0.35–0.40 | 0.60–0.80 | 0.04 | 0.04 | 0.15–0.35 | 1.65–2.00 | 0.70–0.90 | 0.20–0.30 |
| E4337 | 0.35–0.40 | 0.65–0.85 | 0.025 | 0.025 | 0.15–0.35 | 1.65–2.00 | 0.70–0.90 | 0.20–0.30 |
| 4340 | 0.38–0.43 | 0.60–0.80 | 0.04 | 0.04 | 0.15–0.35 | 1.65–2.00 | 0.70–0.90 | 0.20–0.30 |
| E4340 | 0.38–0.43 | 0.65–0.85 | 0.025 | 0.025 | 0.15–0.35 | 1.65–2.00 | 0.70–0.90 | 0.20–0.30 |
| 4422 | 0.20–0.25 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.35–0.45 |
| 4427 | 0.24–0.29 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.35–0.45 |
| 4520 | 0.18–0.23 | 0.45–0.65 | 0.04 | 0.04 | 0.15–0.35 | … | … | 0.45–0.60 |
| 4615 | 0.13–0.18 | 0.45–0.65 | 0.04 | 0.04 | 0.15–0.35 | 1.65–2.00 | … | 0.20–0.30 |
| 4617 | 0.15–0.20 | 0.45–0.65 | 0.04 | 0.04 | 0.15–0.35 | 1.65–2.00 | … | 0.20–0.30 |
| 4620 | 0.17–0.22 | 0.45–0.65 | 0.04 | 0.04 | 0.15–0.35 | 1.65–2.00 | … | 0.20–0.30 |
| 4621 | 0.18–0.23 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 1.65–2.00 | … | 0.20–0.30 |
| 4718 | 0.16–0.21 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.90–1.20 | 0.35–0.55 | 0.30–0.40 |
| 4720 | 0.17–0.22 | 0.50–0.70 | 0.04 | 0.04 | 0.15–0.35 | 0.90–1.20 | 0.35–0.55 | 0.15–0.25 |
| 4815 | 0.13–0.18 | 0.40–0.60 | 0.04 | 0.04 | 0.15–0.35 | 3.25–3.75 | … | 0.20–0.30 |
| 4817 | 0.15–0.20 | 0.40–0.60 | 0.04 | 0.04 | 0.15–0.35 | 3.25–3.75 | … | 0.20–0.30 |
| 4820 | 0.18–0.23 | 0.50–0.70 | 0.04 | 0.04 | 0.15–0.35 | 3.25–3.75 | … | 0.20–0.30 |
| 5015 | 0.12–0.17 | 0.30–0.50 | 0.04 | 0.04 | 0.15–0.35 | … | 0.30–0.50 | … |
| 5046 | 0.43–0.50 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.20–0.35 | … |
| 5115 | 0.13–0.18 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.70–0.90 | … |
| 5120 | 0.17–0.22 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.70–0.90 | … |
| 5130 | 0.28–0.33 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | … |
| 5132 | 0.30–0.35 | 0.60–0.80 | 0.04 | 0.04 | 0.15–0.35 | … | 0.75–1.00 | … |
| 5135 | 0.33–0.38 | 0.60–0.80 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.05 | … |
| 5140 | 0.38–0.43 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.70–0.90 | … |
| 5145 | 0.43–0.48 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.70–0.90 | … |
| 5147 | 0.46–0.51 | 0.70–0.95 | 0.04 | 0.04 | 0.15–0.35 | … | 0.85–1.15 | … |
| 5150 | 0.48–0.53 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.70–0.90 | … |
| 5155 | 0.51–0.59 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.70–0.90 | … |
| 5160 | 0.56–0.64 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.70–0.90 | … |
| 52100E | 0.93–1.05 | 0.25–0.45 | 0.025 | 0.015 | 0.15–0.35 | 0.25 max | 1.35–1.60 | 0.10 max |
| E50100 | 0.98–1.10 | 0.25–0.45 | 0.025 | 0.025 | 0.15–0.35 | … | 0.40–0.60 | … |
| E51100 | 0.98–1.10 | 0.25–0.45 | 0.025 | 0.025 | 0.15–0.35 | … | 0.90–1.15 | … |
| E52100 | 0.98–1.10 | 0.25–0.45 | 0.025 | 0.025 | 0.15–0.35 | … | 1.30–1.60 | … |
| Vanadium | ||||||||
| 6118 | 0.16–0.21 | 0.50–0.70 | 0.04 | 0.04 | 0.15–0.35 | … | 0.50–0.70 | 0.10–0.15 |
| 6120 | 0.17–0.22 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.70–0.90 | 0.10 min |
| 6150 | 0.48–0.53 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | … | 0.80–1.10 | 0.15 min |
| Aluminum | Molybdenum | |||||||
| E7140 | 0.38–0.43 | 0.50–0.70 | 0.025 | 0.025 | 0.15–0.40 | 0.95–1.30 | 1.40–1.80 | 0.30–0.40 |
| Nickel | ||||||||
| 8115 | 0.13–0.18 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.20–0.40 | 0.30–0.50 | 0.08–0.15 |
| 8615 | 0.13–0.18 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8617 | 0.15–0.20 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8620 | 0.18–0.23 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8622 | 0.20–0.25 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8625 | 0.23–0.28 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8627 | 0.25–0.30 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8630 | 0.28–0.33 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8637 | 0.35–0.40 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8640 | 0.38–0.43 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8642 | 0.40–0.45 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8645 | 0.43–0.48 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8650 | 0.48–0.53 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8655 | 0.51–0.59 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8660 | 0.55–0.65 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 8720 | 0.18–0.23 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.20–0.30 |
| 8735 | 0.33–0.38 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.20–0.30 |
| 8740 | 0.38–0.43 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.20–0.30 |
| 8742 | 0.40–0.45 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.20–0.30 |
| 8822 | 0.20–0.25 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.30–0.40 |
| 9255 | 0.51–0.59 | 0.60–0.80 | 0.04 | 0.04 | 1.80–2.20 | … | 0.60–0.80 | … |
| 9260 | 0.56–0.64 | 0.75–1.00 | 0.04 | 0.04 | 1.80–2.20 | … | … | … |
| 9262 | 0.55–0.65 | 0.75–1.00 | 0.04 | 0.04 | 1.80–2.20 | … | 0.25–0.40 | … |
| E9310 | 0.08–0.13 | 0.45–0.65 | 0.025 | 0.025 | 0.15–0.35 | 3.00–3.50 | 1.00–1.40 | 0.08–0.15 |
| 9840 | 0.38–0.42 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.85–1.15 | 0.70–0.90 | 0.20–0.30 |
| 9850 | 0.48–0.53 | 0.70–0.90 | 0.04 | 0.04 | 0.15–0.35 | 0.85–1.15 | 0.70–0.90 | 0.20–0.30 |
| 50B40 | 0.38–0.42 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.40–0.60 | … |
| 50B44 | 0.43–0.48 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.40–0.60 | … |
| 50B46 | 0.43–0.50 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.20–0.35 | … |
| 50B50 | 0.48–0.53 | 0.74–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.40–0.60 | … |
| 50B60 | 0.55–0.65 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.40–0.60 | … |
| 51B60 | 0.56–0.64 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | … | 0.70–0.90 | … |
| 81B45 | 0.43–0.48 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.20–0.40 | 0.35–0.55 | 0.08–0.15 |
| 86B45 | 0.43–0.48 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.40–0.70 | 0.40–0.60 | 0.15–0.25 |
| 94B15 | 0.13–0.18 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.30–0.60 | 0.30–0.50 | 0.08–0.15 |
| 94B17 | 0.15–0.20 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.30–0.60 | 0.30–0.50 | 0.08–0.15 |
| 94B30 | 0.28–0.33 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.30–0.60 | 0.30–0.50 | 0.08–0.15 |
| 94B40 | 0.38–0.43 | 0.75–1.00 | 0.04 | 0.04 | 0.15–0.35 | 0.30–0.60 | 0.30–0.50 | 0.08–0.15 |
B Grades shown in this table with the letter B, such as 50B40, can be expected to have 0.0005 % minimum boron control. A Grades shown in this table with prefix letter E generally are manufactured by the basic-electric-furnace process. All others are normally manufactured by the basic-open-hearth process but may be manufactured by the basic-electric-furnace process with adjustments in phosphorus and sulfur.
C The phosphorus sulfur limitations for each process are as follows:
Basic electric furnace 0.025 max % Acid electric furnace 0.050 max %
Basic open hearth 0.040 max % Acid open hearth 0.050 max %
D Minimum and maximum sulfur content indicates resulfurized steels.
EThe purchaser may specify the following maximum amounts: copper, 0.30 %; aluminum, 0.050 %; and oxygen, 0.0015 %.
Mechanical Property
Typical Tensile Properties, Hardness and Thermal Condition for some of the More Common Grades of Carbon and Alloy Steels
CW—Cold Worked SR—Stress Relieved A—Annealed N—NormalizedA The following are the symbol definitions for the various conditions: HR—Hot Rolle
| Grade | Condi- | Ultimate | Yield | Elongation | Rockwell, | ||||
| Desig- | tionA | Strength, | Strength, | in 2 in. or | Hardness | ||||
| nation | 50 mm, % | B Scale | |||||||
| ksi | MPa | ksi | MPa | ||||||
| 1020 | HR | 50 | 345 | 32 | 221 | 25 | 55 | ||
| CW | 70 | 483 | 60 | 414 | 5 | 75 | |||
| SR | 65 | 448 | 50 | 345 | 10 | 72 | |||
| A | 48 | 331 | 28 | 193 | 30 | 50 | |||
| N | 55 | 379 | 34 | 234 | 22 | 60 | |||
| 1025 | HR | 55 | 379 | 35 | 241 | 25 | 60 | ||
| CW | 75 | 517 | 65 | 448 | 5 | 80 | |||
| SR | 70 | 483 | 55 | 379 | 8 | 75 | |||
| A | 53 | 365 | 30 | 207 | 25 | 57 | |||
| N | 55 | 379 | 36 | 248 | 22 | 60 | |||
| 1035 | HR | 65 | 448 | 40 | 276 | 20 | 72 | ||
| CW | 85 | 586 | 75 | 517 | 5 | 88 | |||
| SR | 75 | 517 | 65 | 448 | 8 | 80 | |||
| A | 60 | 414 | 33 | 228 | 25 | 67 | |||
| N | 65 | 448 | 40 | 276 | 20 | 72 | |||
| 1045 | HR | 75 | 517 | 45 | 310 | 15 | 80 | ||
| CW | 90 | 621 | 80 | 552 | 5 | 90 | |||
| SR | 80 | 552 | 70 | 483 | 8 | 85 | |||
| A | 65 | 448 | 35 | 241 | 20 | 72 | |||
| N | 75 | 517 | 48 | 331 | 15 | 80 | |||
| 1050 | HR | 80 | 552 | 50 | 345 | 10 | 85 | ||
| SR | 82 | 565 | 70 | 483 | 6 | 86 | |||
| A | 68 | 469 | 38 | 262 | 18 | 74 | |||
| N | 78 | 538 | 50 | 345 | 12 | 82 | |||
| 1118 | HR | 50 | 345 | 35 | 241 | 25 | 55 | ||
| CW | 75 | 517 | 60 | 414 | 5 | 80 | |||
| SR | 70 | 483 | 55 | 379 | 8 | 75 | |||
| A | 50 | 345 | 30 | 207 | 25 | 55 | |||
| N | 55 | 379 | 35 | 241 | 20 | 60 | |||
| 1137 | HR | 70 | 483 | 40 | 276 | 20 | 75 | ||
| CW | 80 | 552 | 65 | 448 | 5 | 85 | |||
| SR | 75 | 517 | 60 | 414 | 8 | 80 | |||
| A | 65 | 448 | 35 | 241 | 22 | 72 | |||
| N | 70 | 483 | 43 | 296 | 15 | 75 | |||
| 4130 | HR | 90 | 621 | 70 | 483 | 20 | 89 | ||
| SR | 105 | 724 | 85 | 586 | 10 | 95 | |||
| A | 75 | 517 | 55 | 379 | 30 | 81 | |||
| N | 90 | 621 | 60 | 414 | 20 | 89 | |||
| 4140 | HR | 120 | 855 | 90 | 621 | 15 | 100 | ||
| SR | 120 | 855 | 100 | 689 | 10 | 100 | |||
| A | 80 | 552 | 60 | 414 | 25 | 85 | |||
| N | 120 | 855 | 90 | 621 | 20 | 100 | |||
d
Test Requirement
Hardness Test,Tension Tests, Nondestructive Tests，Steel Cleanliness, Hardenability, Flaring Test
Supply Ability
Supply Ability: 2000 Tons Per Month Per Grade Of ASTM A519-2006 Steel Pipe
Packaging
In Bundles And In Strong Wooden Box
Delivery
7-14 days if in stock, 30-45 days to produce
Payment
30% depsoit, 70% L/C or B/L copy or 100% L/C at sight
Product Detail
Mechanical/Chemical&Fertilizer Pipes
GB/T8162-2008
ASTM A519-2006
BS EN 10210-1-2006
ASTM A53/A53M-2012
GB9948-2006
GB6479-2013
GB/T 17396-2009
Product detail pictures:
Related Product Guide:
We will devote ourselves to providing our esteemed customers with the most enthusiastically thoughtful services for 2019 Good Quality Alloy Steel Pipe Properties - Seamless carbon steel and alloy mechanical tubes – Sanonpipe , The product will supply to all over the world, such as: azerbaijan , Holland , Bangalore , Besides there are also professional production and management , advanced production equipment to assure our quality and delivery time , our company pursues the principle of good faith, high-quality and high-efficiency. We guarantee that our company will try our best to reduce customer purchase cost, shorten the period of purchase, stable products quality, increase customers' satisfaction and achieve win-win situation .
By Odelia
from Cologne
- 2018.07.26 16:51
Speaking of this cooperation with the Chinese manufacturer, I just want to say"well dodne", we are very satisfied.
By Eve
from Leicester
- 2017.06.16 18:23
