Best Price on P12 Alloy Steel Pipe Manufacturer - APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

We thinks what buyers think, the urgency of urgency to act during the interests of a purchaser position of theory, allowing for much better high-quality, reduced processing costs, charges are more reasonable, won the new and outdated consumers the support and affirmation for Alloy Low Pressure Boiler Pipe , Api 5l Psl1/ Psl2 , Alloy Steel Pipe 15crmo , Your support is our eternal power! Warmly welcome customers at home and abroad to visit our company.
Best Price on P12 Alloy Steel Pipe Manufacturer - APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe Detail:

Overview

Application

The pipeline is used to transport the oil, steam and water drawn from the ground to the oil and gas industry enterprises through the pipeline

Main Grade

Grade for API 5L line pipe steel: Gr.B X42 X52 X60 X65 X70

Chemical Component

 Steel Grade (Steel Name) Mass Fraction, Based on Heat and Product Analyses a,g%
C Mn P S V Nb Ti
max b max b min max max max max max
Seamless Pipe
L175 or A25 0.21 0.60 0.030 0.030
L175P or A25P 0.21 0.60 0.045 0.080 0.030
L210 or A 0.22 0.90 0.030 0.030
L245 or B 0.28 1.20 0.030 0.030 c,d c,d d
L290 or X42 0.28 1.30 0.030 0.030 d d d
L320 or X46 0.28 1.40 0.030 0.030 d d d
L360 or X52 0.28 1.40 0.030 0.030 d d d
L390 or X56 0.28 1.40 0.030 0.030 d d d
L415 or X60 0.28 e 1.40 e 0.030 0.030 f f f
L450 or X65 0.28 e 1.40 e 0.030 0.030 f f f
L485 or X70 0.28 e 1.40 e 0.030 0.030 f f f
Welded Pipe
L175 or A25 0.21 0.60 0.030 0.030
L175P or A25P 0.21 0.60 0.045 0.080 0.030
L210 or A 0.22 0.90 0.030 0.030
L245 or B 0.26 1.20 0.030 0.030 c,d c,d d
L290 or X42 0.26 1.30 0.030 0.030 d d d
L320 or X46 0.26 1.40 0.030 0.030 d d d
L360 or X52 0.26 1.40 0.030 0.030 d d d
L390 or X56 0.26 1.40 0.030 0.030 d d d
L415 or X60 0.26 e 1.40 e 0.030 0.030 f f f
L450 or X65 0.26 e 1.45 e 0.030 0.030 f f f
L485 or X70 0.26 e 1.65 e 0.030 0.030 f f f

a Cu ≤ 0.50 %; Ni ≤ 0.50 %; Cr ≤ 0.50 % and Mo ≤ 0.15 %.

b For each reduction of 0.01 % below the specified maximum concentration for carbon, an increase of 0.05 % above the specified maximum concentration for Mn is permissible, up to a maximum of 1.65 % for grades ≥ L245 or B, but ≤ L360 or X52; up to a maximum of 1.75 % for grades > L360 or X52, but < L485 or X70; and up to a maximum of 2.00 % for Grade L485 or X70.

c Unless otherwise agreed, Nb + V ≤ 0.06 %.

d Nb + V + Ti ≤ 0.15 %.

e Unless otherwise agreed.

f Unless otherwise agreed, Nb + V + Ti ≤ 0.15 %.

g No deliberate addition of B is permitted and the residual B ≤ 0.001 %.

Mechanical Property

 

 

 

Pipe Grade

 Pipe Body of Seamless and Welded Pipe Weld Seam of EW, LW, SAW, and COWPipe
Yield Strength a 

Rt0.5

Tensile Strength a 

Rm

Elongation(on 50 mm or 2 in.)

Af

Tensile Strength b 

Rm

MPa (psi) MPa (psi) % MPa (psi)
min min min min
L175 or A25 175 (25,400) 310 (45,000) c 310 (45,000)
L175P or A25P 175 (25,400) 310 (45,000) c 310 (45,000)
L210 or A 210 (30,500) 335 (48,600) c 335 (48,600)
L245 or B 245 (35,500) 415 (60,200) c 415 (60,200)
L290 or X42 290 (42,100) 415 (60,200) c 415 (60,200)
L320 or X46 320 (46,400) 435 (63,100) c 435 (63,100)
L360 or X52 360 (52,200) 460 (66,700) c 460 (66,700)
L390 or X56 390 (56,600) 490 (71,100) c 490 (71,100)
L415 or X60 415 (60,200) 520 (75,400) c 520 (75,400)
L450 or X65 450 (65,300) 535 (77,600) c 535 (77,600)
L485 or X70 485 (70,300) 570 (82,700) c 570 (82,700)
a For intermediate grades, the difference between the specified minimum tensile strength and the specified minimum yield strength for the pipe body shall be as given in the table for the next higher grade.b For intermediate grades, the specified minimum tensile strength for the weld seam shall be the same value as was determined for the pipe body using footnote a).

c The specified minimum elongation, Af, expressed in percent and rounded to the nearest percent, shall be as determined using the following equation:

 

where

C is 1940 for calculations using SI units and 625,000 for calculations using USC units;

Axc is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches), as follows:

1) for circular cross-section test pieces, 130 mm2 (0.20 in.2) for 12.7 mm (0.500 in.) and 8.9 mm (0.350 in.) diameter  test pieces; 65 mm2 (0.10 in.2) for 6.4 mm (0.250 in.) diameter test pieces;

2) for full-section test pieces, the lesser of a) 485 mm2 (0.75 in.2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest     10 mm2 (0.01 in.2);

3) for strip test pieces, the lesser of a) 485 mm2 (0.75 in.2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece  and the specified  wall  thickness  of the  pipe,  rounded to  the  nearest  10 mm2 (0.01 in.2);

U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch).

Test Requirement

Test:Hydrostatic pressure, flattening, hardness, CVN impact, NDT

Supply Ability

Supply Ability: 1000 Tons Per Month Per Grade of API 5L carbon Steel Pipe

Packaging

In Bundles And In Strong Wooden Box

Delivery

7-14 days if in stock, 30-45 days to produce

Payment

30% depsoit, 70% L/C or B/L copy   or  100% L/C at sight

Product Detail

Petroleum Pipes Structure Pipes


Product detail pictures:

Best Price on P12 Alloy Steel Pipe Manufacturer -
 APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe detail pictures

Best Price on P12 Alloy Steel Pipe Manufacturer -
 APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe detail pictures

Best Price on P12 Alloy Steel Pipe Manufacturer -
 APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe detail pictures


Related Product Guide:

We've numerous great employees customers excellent at promoting, QC, and working with kinds of troublesome difficulty inside the generation method for Best Price on P12 Alloy Steel Pipe Manufacturer - APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe , The product will supply to all over the world, such as: Cyprus , San Francisco , Bulgaria , During the 10 years of operating, our company always try our best to bring consumption satisfaction for user, built a brand name for ourselves and a solid position in the international market with major partners come from many countries such as Germany, Israel, Ukraine, United Kingdom, Italy, Argentina, France, Brazil, and so on. Last but not least, price of our products are very suitable and have fairly high competition with other companies.
  • This is a very professional wholesaler, we always come to their company for procurement, good quality and cheap.
    5 Stars By Victoria from Norwegian - 2018.09.23 18:44
    In China, we have purchased many times, this time is the most successful and most satisfactory, a sincere and realiable Chinese manufacturer!
    5 Stars By Edwina from Auckland - 2017.08.15 12:36
    Write your message here and send it to us