Cheapest Price P11 Alloy Steel Pipe Manufacturer - APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe
Cheapest Price P11 Alloy Steel Pipe Manufacturer - APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe Detail:
Overview
Application
The pipeline is used to transport the oil, steam and water drawn from the ground to the oil and gas industry enterprises through the pipeline
Main Grade
Grade for API 5L line pipe steel: Gr.B X42 X52 X60 X65 X70
Chemical Component
Steel Grade (Steel Name) | Mass Fraction, Based on Heat and Product Analyses a,g% | |||||||
C | Mn | P | S | V | Nb | Ti | ||
max b | max b | min | max | max | max | max | max | |
Seamless Pipe | ||||||||
L175 or A25 | 0.21 | 0.60 | — | 0.030 | 0.030 | — | — | — |
L175P or A25P | 0.21 | 0.60 | 0.045 | 0.080 | 0.030 | — | — | — |
L210 or A | 0.22 | 0.90 | — | 0.030 | 0.030 | — | — | — |
L245 or B | 0.28 | 1.20 | — | 0.030 | 0.030 | c,d | c,d | d |
L290 or X42 | 0.28 | 1.30 | — | 0.030 | 0.030 | d | d | d |
L320 or X46 | 0.28 | 1.40 | — | 0.030 | 0.030 | d | d | d |
L360 or X52 | 0.28 | 1.40 | — | 0.030 | 0.030 | d | d | d |
L390 or X56 | 0.28 | 1.40 | — | 0.030 | 0.030 | d | d | d |
L415 or X60 | 0.28 e | 1.40 e | — | 0.030 | 0.030 | f | f | f |
L450 or X65 | 0.28 e | 1.40 e | — | 0.030 | 0.030 | f | f | f |
L485 or X70 | 0.28 e | 1.40 e | — | 0.030 | 0.030 | f | f | f |
Welded Pipe | ||||||||
L175 or A25 | 0.21 | 0.60 | — | 0.030 | 0.030 | — | — | — |
L175P or A25P | 0.21 | 0.60 | 0.045 | 0.080 | 0.030 | — | — | — |
L210 or A | 0.22 | 0.90 | — | 0.030 | 0.030 | — | — | — |
L245 or B | 0.26 | 1.20 | — | 0.030 | 0.030 | c,d | c,d | d |
L290 or X42 | 0.26 | 1.30 | — | 0.030 | 0.030 | d | d | d |
L320 or X46 | 0.26 | 1.40 | — | 0.030 | 0.030 | d | d | d |
L360 or X52 | 0.26 | 1.40 | — | 0.030 | 0.030 | d | d | d |
L390 or X56 | 0.26 | 1.40 | — | 0.030 | 0.030 | d | d | d |
L415 or X60 | 0.26 e | 1.40 e | — | 0.030 | 0.030 | f | f | f |
L450 or X65 | 0.26 e | 1.45 e | — | 0.030 | 0.030 | f | f | f |
L485 or X70 | 0.26 e | 1.65 e | — | 0.030 | 0.030 | f | f | f |
a Cu ≤ 0.50 %; Ni ≤ 0.50 %; Cr ≤ 0.50 % and Mo ≤ 0.15 %. b For each reduction of 0.01 % below the specified maximum concentration for carbon, an increase of 0.05 % above the specified maximum concentration for Mn is permissible, up to a maximum of 1.65 % for grades ≥ L245 or B, but ≤ L360 or X52; up to a maximum of 1.75 % for grades > L360 or X52, but < L485 or X70; and up to a maximum of 2.00 % for Grade L485 or X70. c Unless otherwise agreed, Nb + V ≤ 0.06 %. d Nb + V + Ti ≤ 0.15 %. e Unless otherwise agreed. f Unless otherwise agreed, Nb + V + Ti ≤ 0.15 %. g No deliberate addition of B is permitted and the residual B ≤ 0.001 %. |
Mechanical Property
|
Pipe Body of Seamless and Welded Pipe | Weld Seam of EW, LW, SAW, and COWPipe | ||
Yield Strength a
Rt0.5 |
Tensile Strength a
Rm |
Elongation(on 50 mm or 2 in.)
Af |
Tensile Strength b
Rm |
|
MPa (psi) | MPa (psi) | % | MPa (psi) | |
min | min | min | min | |
L175 or A25 | 175 (25,400) | 310 (45,000) | c | 310 (45,000) |
L175P or A25P | 175 (25,400) | 310 (45,000) | c | 310 (45,000) |
L210 or A | 210 (30,500) | 335 (48,600) | c | 335 (48,600) |
L245 or B | 245 (35,500) | 415 (60,200) | c | 415 (60,200) |
L290 or X42 | 290 (42,100) | 415 (60,200) | c | 415 (60,200) |
L320 or X46 | 320 (46,400) | 435 (63,100) | c | 435 (63,100) |
L360 or X52 | 360 (52,200) | 460 (66,700) | c | 460 (66,700) |
L390 or X56 | 390 (56,600) | 490 (71,100) | c | 490 (71,100) |
L415 or X60 | 415 (60,200) | 520 (75,400) | c | 520 (75,400) |
L450 or X65 | 450 (65,300) | 535 (77,600) | c | 535 (77,600) |
L485 or X70 | 485 (70,300) | 570 (82,700) | c | 570 (82,700) |
a For intermediate grades, the difference between the specified minimum tensile strength and the specified minimum yield strength for the pipe body shall be as given in the table for the next higher grade.b For intermediate grades, the specified minimum tensile strength for the weld seam shall be the same value as was determined for the pipe body using footnote a).
c The specified minimum elongation, Af, expressed in percent and rounded to the nearest percent, shall be as determined using the following equation:
where C is 1940 for calculations using SI units and 625,000 for calculations using USC units; Axc is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches), as follows: 1) for circular cross-section test pieces, 130 mm2 (0.20 in.2) for 12.7 mm (0.500 in.) and 8.9 mm (0.350 in.) diameter test pieces; 65 mm2 (0.10 in.2) for 6.4 mm (0.250 in.) diameter test pieces; 2) for full-section test pieces, the lesser of a) 485 mm2 (0.75 in.2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.01 in.2); 3) for strip test pieces, the lesser of a) 485 mm2 (0.75 in.2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.01 in.2); U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch). |
Test Requirement
Test:Hydrostatic pressure, flattening, hardness, CVN impact, NDT
Supply Ability
Supply Ability: 1000 Tons Per Month Per Grade of API 5L carbon Steel Pipe
Packaging
In Bundles And In Strong Wooden Box
Delivery
7-14 days if in stock, 30-45 days to produce
Payment
30% depsoit, 70% L/C or B/L copy or 100% L/C at sight
Product Detail
Petroleum Pipes Structure Pipes
Product detail pictures:
Related Product Guide:
Our eternal pursuits are the attitude of "regard the market, regard the custom, regard the science" as well as the theory of "quality the basic, believe in the 1st and management the advanced" for Cheapest Price P11 Alloy Steel Pipe Manufacturer - APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe , The product will supply to all over the world, such as: Algeria , Croatia , Birmingham , We take measure at any expense to achieve essentially the most up-to-date equipment and approaches. The packing of nominated brand is our a further distinguishing feature. The items to assure years of trouble-free service has attracted a great deal customers. The solutions are obtainable in improved designs and richer assortment, they're created scientifically of purely raw supplies. It readily available in a variety of designs and specifications for your selection. The most recent kinds are a great deal better than the preceding one particular and they are quite popular with lots of prospects.
By Elma from Zurich - 2017.01.28 18:53
The goods we received and the sample sales staff display to us have the same quality, it is really a creditable manufacturer.
By Martin Tesch from Malawi - 2018.02.21 12:14