Newly Arrival Erw Steel Pipe - APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

We've been commitment to offer the competitive rate ,outstanding merchandise good quality, too as fast delivery for Steel Pipes , Alloy Steel Pipe Asme 335 , Tube , We warmly welcome customers, business associations and friends from all over the world to contact us and seek cooperation for mutual benefits.
Newly Arrival Erw Steel Pipe - APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe Detail:

Overview

Application

The pipeline is used to transport the oil, steam and water drawn from the ground to the oil and gas industry enterprises through the pipeline

Main Grade

Grade for API 5L line pipe steel: Gr.B X42 X52 X60 X65 X70

Chemical Component

 Steel Grade (Steel Name) Mass Fraction, Based on Heat and Product Analyses a,g%
C Mn P S V Nb Ti
max b max b min max max max max max
Seamless Pipe
L175 or A25 0.21 0.60 0.030 0.030
L175P or A25P 0.21 0.60 0.045 0.080 0.030
L210 or A 0.22 0.90 0.030 0.030
L245 or B 0.28 1.20 0.030 0.030 c,d c,d d
L290 or X42 0.28 1.30 0.030 0.030 d d d
L320 or X46 0.28 1.40 0.030 0.030 d d d
L360 or X52 0.28 1.40 0.030 0.030 d d d
L390 or X56 0.28 1.40 0.030 0.030 d d d
L415 or X60 0.28 e 1.40 e 0.030 0.030 f f f
L450 or X65 0.28 e 1.40 e 0.030 0.030 f f f
L485 or X70 0.28 e 1.40 e 0.030 0.030 f f f
Welded Pipe
L175 or A25 0.21 0.60 0.030 0.030
L175P or A25P 0.21 0.60 0.045 0.080 0.030
L210 or A 0.22 0.90 0.030 0.030
L245 or B 0.26 1.20 0.030 0.030 c,d c,d d
L290 or X42 0.26 1.30 0.030 0.030 d d d
L320 or X46 0.26 1.40 0.030 0.030 d d d
L360 or X52 0.26 1.40 0.030 0.030 d d d
L390 or X56 0.26 1.40 0.030 0.030 d d d
L415 or X60 0.26 e 1.40 e 0.030 0.030 f f f
L450 or X65 0.26 e 1.45 e 0.030 0.030 f f f
L485 or X70 0.26 e 1.65 e 0.030 0.030 f f f

a Cu ≤ 0.50 %; Ni ≤ 0.50 %; Cr ≤ 0.50 % and Mo ≤ 0.15 %.

b For each reduction of 0.01 % below the specified maximum concentration for carbon, an increase of 0.05 % above the specified maximum concentration for Mn is permissible, up to a maximum of 1.65 % for grades ≥ L245 or B, but ≤ L360 or X52; up to a maximum of 1.75 % for grades > L360 or X52, but < L485 or X70; and up to a maximum of 2.00 % for Grade L485 or X70.

c Unless otherwise agreed, Nb + V ≤ 0.06 %.

d Nb + V + Ti ≤ 0.15 %.

e Unless otherwise agreed.

f Unless otherwise agreed, Nb + V + Ti ≤ 0.15 %.

g No deliberate addition of B is permitted and the residual B ≤ 0.001 %.

Mechanical Property

 

 

 

Pipe Grade

 Pipe Body of Seamless and Welded Pipe Weld Seam of EW, LW, SAW, and COWPipe
Yield Strength a 

Rt0.5

Tensile Strength a 

Rm

Elongation(on 50 mm or 2 in.)

Af

Tensile Strength b 

Rm

MPa (psi) MPa (psi) % MPa (psi)
min min min min
L175 or A25 175 (25,400) 310 (45,000) c 310 (45,000)
L175P or A25P 175 (25,400) 310 (45,000) c 310 (45,000)
L210 or A 210 (30,500) 335 (48,600) c 335 (48,600)
L245 or B 245 (35,500) 415 (60,200) c 415 (60,200)
L290 or X42 290 (42,100) 415 (60,200) c 415 (60,200)
L320 or X46 320 (46,400) 435 (63,100) c 435 (63,100)
L360 or X52 360 (52,200) 460 (66,700) c 460 (66,700)
L390 or X56 390 (56,600) 490 (71,100) c 490 (71,100)
L415 or X60 415 (60,200) 520 (75,400) c 520 (75,400)
L450 or X65 450 (65,300) 535 (77,600) c 535 (77,600)
L485 or X70 485 (70,300) 570 (82,700) c 570 (82,700)
a For intermediate grades, the difference between the specified minimum tensile strength and the specified minimum yield strength for the pipe body shall be as given in the table for the next higher grade.b For intermediate grades, the specified minimum tensile strength for the weld seam shall be the same value as was determined for the pipe body using footnote a).

c The specified minimum elongation, Af, expressed in percent and rounded to the nearest percent, shall be as determined using the following equation:

 

where

C is 1940 for calculations using SI units and 625,000 for calculations using USC units;

Axc is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches), as follows:

1) for circular cross-section test pieces, 130 mm2 (0.20 in.2) for 12.7 mm (0.500 in.) and 8.9 mm (0.350 in.) diameter  test pieces; 65 mm2 (0.10 in.2) for 6.4 mm (0.250 in.) diameter test pieces;

2) for full-section test pieces, the lesser of a) 485 mm2 (0.75 in.2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest     10 mm2 (0.01 in.2);

3) for strip test pieces, the lesser of a) 485 mm2 (0.75 in.2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece  and the specified  wall  thickness  of the  pipe,  rounded to  the  nearest  10 mm2 (0.01 in.2);

U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch).

Test Requirement

Test:Hydrostatic pressure, flattening, hardness, CVN impact, NDT

Supply Ability

Supply Ability: 1000 Tons Per Month Per Grade of API 5L carbon Steel Pipe

Packaging

In Bundles And In Strong Wooden Box

Delivery

7-14 days if in stock, 30-45 days to produce

Payment

30% depsoit, 70% L/C or B/L copy   or  100% L/C at sight

Product Detail

Petroleum Pipes Structure Pipes


Product detail pictures:

Newly Arrival Erw Steel Pipe -
 APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe detail pictures

Newly Arrival Erw Steel Pipe -
 APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe detail pictures

Newly Arrival Erw Steel Pipe -
 APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe detail pictures


Related Product Guide:

In order to best meet client's needs, all of our operations are strictly performed in line with our motto "High Quality, Competitive Price, Fast Service" for Newly Arrival Erw Steel Pipe - APISPEC5L-2012 Carbon Seamless Steel Line Pipe 46th edition – Sanonpipe , The product will supply to all over the world, such as: Senegal , Estonia , Malaysia , Our products are sold to the Middle East, Southeast Asia, Africa, Europe, America and other regions, and are favorably appraised by clients. To benefit from our strong OEM/ODM capabilities and considerate services, please contact us today. We will sincerely create and share success with all clients.
  • This company has the idea of "better quality, lower processing costs, prices are more reasonable", so they have competitive product quality and price, that's the main reason we chose to cooperate.
    5 Stars By Jerry from Vietnam - 2018.05.15 10:52
    Production management mechanism is completed, quality is guaranteed, high credibility and service let the cooperation is easy, perfect!
    5 Stars By Louis from Croatia - 2018.06.12 16:22
    Write your message here and send it to us