Super Lowest Price A106/A53/Asme Sa106 Sa53 - Seamless Alloy Steel Boiler Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

Our corporation puts emphasis about the administration, the introduction of talented staff, plus the construction of team building, attempting hard to improve the quality and liability consciousness of team members. Our organization successfully attained IS9001 Certification and European CE Certification of Impact Test , Seamless Steel Pipe Standard , Erw Steel Pipe Exporter , Our enterprise insists on innovation to promote the sustainable advancement of organization, and make us become the domestic high-quality suppliers.
Super Lowest Price A106/A53/Asme Sa106 Sa53 - Seamless Alloy Steel Boiler Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe Detail:

Overview

Application

It is mainly used to make high-quality alloy steel pipe for high pressure boiler pipe, heat exchanger pipe and super heat pipe

Main Grade

Grade of high-quality Alloy steel: T2,T12,T11,T22, T91, T92 etc.

Chemical Component

Steel Grade Chemical Composition%
C Si Mn P, S Max Cr Mo Ni Max V Al Max W B
T2 0.10~0.20 0.10~0.30 0.30~0.61 0.025 0.50~0.81 0.44~0.65
T11 0.05~0.15 0.50~1.00 0.30~0.60 0.025 1.00~1.50 0.44~0.65
T12 0.05~0.15 Max 0.5 0.30~0.61 0.025 0.80~1.25 0.44~0.65
T22 0.05~0.15 Max 0.5 0.30~0.60 0.025 1.90~2.60 0.87~1.13
T91 0.07~0.14 0.20~0.50 0.30~0.60 0.02 8.0~9.5 0.85~1.05 0.4 0.18~0.25 0.015
T92 0.07~0.13 Max 0.5 0.30~0.60 0.02 8.5~9.5 0.30~0.60 0.4 0.15~0.25 0.015 1.50~2.00 0.001~0.006

For T91 other than above also includes Nickel 0.4, Va 0.18-0.25, Ni 0.06-0.10, Ni 0.03-0.07, Al 0.02, Ti 0.01, Zr 0.01. A Maximum, unless range or minimum is indicated. Where ellipses (…) appear in this table, there is no requirement, and analysis for the element need not be determined or reported. B It is permissible to order T2 and T12 with a sulfur content of 0.045 max. C Alternatively, in lieu of this ratio minimum, the material shall have a minimum hardness of 275 HV in the hardened condition, defined as after austenitizing and cooling to room temperature but prior to tempering. Hardness testing shall be performed at mid-thickness of the product. Hardness test frequency shall be two samples of product per heat treatment lot and the hardness testing results shall be reported on the material test report.

Mechanical Property

Steel Grade Mechanical Properties
T. S Y. P Elongation Hardness
T2 ≥ 415MPa ≥ 205MPa ≥ 30% 163HBW(85HRB)
T11 ≥ 415MPa ≥ 205MPa ≥ 30% 163HBW(85HRB)
T12 ≥ 415MPa ≥ 220MPa ≥ 30% 163HBW(85HRB)
T22 ≥ 415MPa ≥ 205MPa ≥ 30% 163HBW(85HRB)
T91 ≥ 585MPa ≥ 415MPa ≥ 20% 250HBW(25HRB)
T92 ≥ 620MPa ≥ 440MPa ≥ 20% 250HBW(25HRB)

Tolerance

Permitted Variations in  Wall thickness

Wallthickess %
outside
diameter
in.
mm
0.095
2.4
and under
over0.095
to 0.15
2.4-3.8
incl.
over 0.15
to 0.18
3.8-4.6
incl
over 0.18
to 4.6
                                          over under over under over under over under
seamless, hot finished
4inch and under                   40   0     35    0     33    0    28   0
over 4 inch     ..     ..            35    0     33    0    28   0
seamless, cold finished
over  under
11/2 and under 20     0
over 11/2 22     0

The permitted variations in wall thickness apply only to tube , except internal-upset tubes, as rolled or cold finished

and before swaging,expanding ,bending,polishing,or other fabricating operations

Permitted Variations in  Outside Diameter

outside diameter (mm) Pemitted Variation( mm)
hot finished seamless tube over under
4″ (100mm)and under 0.4 0.8
4-71/2″(100-200mm) 0.4 1.2
71/2-9“(200-225) 0.4 1.6
Welded tubes and cold finished seamless tubes
under1″(25mm) 0.1 0.11
1-11/2″(25-40mm) 0.15 0.15
11/2-2″(40-50mm) 0.2 0.2
2-21/2″(50-65mm) 0.25 0.25
21/2-3″(65-75mm) 0.3 0.3
3-4″(75-100mm) 0.38 0.38
4-71/2″(100-200mm) 0.38 0.64
71/2-9“(200-225) 0.38 1.14

Test Requirement

Hydraustatic Test:

The Steel Pipe Should Be Tested Hydraulically One By One. The Maximum Test Pressure Is 20 MPa. Under The Test Pressure, The Stabilization Time Should Be Not Less Than 10 S, And The Steel Pipe Should Not Leak. Or The Hydraulic Test Can Be Replaced By Eddy Current Testing Or Magnetic Flux Leakage Testing.

Nondestructive Test:

Pipes That Require More Inspection Should Be Ultrasonically Inspected One By One. After The Negotiation Requires The Consent Of The Party And Is Specified In The Contract, Other Non-Destructive Testing Can Be Added.

Flattening Test:

Tubes With An Outer Diameter Greater Than 22 Mm Shall Be Subjected To A Flattening Test. No Visible Delamination, White Spots, Or Impurities Should Occur During The Entire Experiment.

Hardness Test:

For Pipe Of Grades P91, P92, P122, And P911, Brinell, Vickers, Or Rockwell Hardness Tests Shall Be Made On A Specimen From Each Lot

 

Product Detail

Boiler Tube


1


GB/T5310-2017


A106 Boiler Pipe


ASME SA-106/SA-106M-2015


carbon steel pipe


ASTMA210(A210M)-2012


2


ASME SA-213/SA-213M


boiler pipe IBR


ASTM A335/A335M-2018


Product detail pictures:

Super Lowest Price A106/A53/Asme Sa106 Sa53 -
 Seamless Alloy Steel Boiler  Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe detail pictures

Super Lowest Price A106/A53/Asme Sa106 Sa53 -
 Seamless Alloy Steel Boiler  Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe detail pictures

Super Lowest Price A106/A53/Asme Sa106 Sa53 -
 Seamless Alloy Steel Boiler  Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe detail pictures


Related Product Guide:

"Quality to start with, Honesty as base, Sincere company and mutual profit" is our idea, as a way to build constantly and pursue the excellence for Super Lowest Price A106/A53/Asme Sa106 Sa53 - Seamless Alloy Steel Boiler Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe , The product will supply to all over the world, such as: Grenada , Malta , New Zealand , With a wide range, good quality, reasonable prices and stylish designs, our products are extensively used in this field and other industries. We welcome new and old customers from all walks of life to contact us for future business relationships and achieving mutual success! We welcome customers, business associations and friends from all parts of the world to contact us and seek cooperation for mutual benefits.
  • In general, we are satisfied with all aspects, cheap, high-quality, fast delivery and good procuct style, we will have follow-up cooperation!
    5 Stars By Dawn from London - 2017.06.19 13:51
    The product classification is very detailed that can be very accurate to meet our demand, a professional wholesaler.
    5 Stars By Matthew Tobias from Jersey - 2017.02.28 14:19
    Write your message here and send it to us